ProAiir QuickEZ Skeleton Hand Normal sjabloon

ProAiir QuickEZ Skeleton Hand Normal Stencil

With the QuickEZ Skeleton Hand Normal stencil, you put a sharp skeleton hand on a face, neck or arm in seconds. Press it down, spray or dab with a make-up sponge, lift the stencil off, done. It's the quickest route to a crisp horror detail, whether you're working with an airbrush or just a finger sponge.

What is the QuickEZ Skeleton Hand Normal stencil?

A reusable face paint stencil made from flexible, semi-transparent 7 mil mylar (approximately 0.18 mm thick).

The designs shown in the product photos are examples; the colour that lands on the skin is the one you choose with your own paint.

Size: approx. 11.4 x 14 cm, one design per stencil. The tab has a hole so you can hang it on a keyring or stencil rack. This is the Normal variant; a larger version is available as Skeleton Hand Large.

Why pick this stencil?

• Airbrush and hand application. Works with ProAiir Hybrid, ProAiir Ink, Endura, and with a sponge and water-activated face paint. You pick the technique that suits the job.
• Fast results. Press down, airbrush or dab, lift off, done. Perfect when you're working through a long queue of faces at a Halloween event or horror show.
• Reusable. Mylar is durable and flexible. Clean it properly and store it flat, and it'll last you many Halloweens.
• Follows the shape of the skin. The thin, flexible mylar sits neatly on cheeks, foreheads, necks and arms, even on rounded surfaces.

How to use the stencil

1. Hold the stencil flat against the skin where you want the skeleton hand to appear.
2. Spray with the airbrush or dab with a damp make-up sponge.
3. Lift the stencil straight up. Don't slide it across the skin or the lines will blur.

Tip for water-activated face paint: keep your sponge damp, not wet. Too much moisture and the paint seeps under the edges, giving you fuzzy lines.

Cleaning and storage

Rinse the stencil after use with lukewarm water and mild soap. Pat it dry gently and leave it flat until fully dry. Don't roll it, don't fold it, or the mylar will develop permanent creases.

Used ProAiir Hybrid? Rub a thin layer of mild soap into the stencil first, then rinse with lukewarm water. That releases the alcohol-based paint from the mylar.

For storage: hang the stencil by the tab hole, or keep it flat between two sheets of paper in a folder.

What can you use it for?

• Halloween makeup: Skeleton Hand Normal on face, neck or arm for an atmospheric horror look
• SFX and cosplay: Skeleton Hand Normal as a building block for zombie, vampire or grim-reaper characters
• Bodypaint: Skeleton Hand Normal in a full body paint for Halloween parties or horror shows
• Theatre and film: Skeleton Hand Normal for stage and camera work where speed matters
• Festivals and photoshoots: Skeleton Hand Normal as a statement detail in a gothic or horror look

Contents

1 reusable ProAiir QuickEZ Skeleton Hand Normal stencil in flexible mylar (7 mil), approx. 11.4 x 14 cm, single design.

Other QuickEz stencils

If this horror theme fits your work, take a look at these stencils from the same range:

• ProAiir QuickEZ Skeleton Hand Large: the larger format of the same skeleton hand design, ideal for body paint or bigger work surfaces.
• ProAiir QuickEZ Blood Cells: blood cell pattern for realistic SFX effects on skin or body.
• ProAiir QuickEZ Bloody Eyes: bloody eyes motif as a chilling detail in a horror or zombie look.

Browse the full ProAiir QuickEZ range with over 60 patterns and designs.

The product photo shows an example face- or body-paint effect with this stencil. The Mylar stencil itself is semi-translucent; the final colour depends on the makeup or airbrush paint you choose.