ProAiir QuickEZ Topper 2 Princess sjabloon

ProAiir QuickEZ Topper 2 Princess Stencil

With the QuickEZ Topper 2 Princess you have an elegant princess motif on the skin in seconds. Apply with an airbrush, a face paint sponge or a finger sponge, lift the stencil, done. The quickest route to a fantasy or glamour detail on the cheek, shoulder or décolletage.

What is the QuickEZ Topper 2 Princess stencil?

A reusable face paint stencil made from flexible, semi-transparent 7 mil mylar (approximately 0.18 mm thick).

The designs shown in the product photos are examples; the colour that lands on the skin is entirely your choice of face paint.

Size: approx. 11.4 x 14 cm, one design per stencil. The tab has a hole so you can hang the stencil on a keyring or stencil rack.

Why pick this stencil?

• Airbrush and manual. The stencil works with your ProAiir Hybrid, ProAiir Ink, Endura, or simply with a sponge and water-activated face paint. You choose the technique that suits the job.
• Quick results. Press down, airbrush or stamp, lift, done. Perfect when you have a long queue of faces at a party or festival.
• Reusable. Mylar is durable and flexible. Clean it properly and store it flat, and it will last you through many events.
• Follows the contours of the skin. The mylar is thin and pliable, so it sits neatly against cheeks, foreheads and décolletage.

How to use the stencil

1. Hold the stencil flat against the skin where you want the princess motif.
2. Spray with the airbrush or dab with a damp face paint sponge.
3. Lift the stencil straight up. Do not slide it across the skin or the edges will smear.

Tip for water-activated face paint: keep your sponge damp, not wet. Too much moisture and the paint seeps under the edges, making your lines blurry.

Cleaning and storage

Rinse the stencil with lukewarm water and mild soap after use. Pat it gently dry and lay it flat until fully dry. Do not roll or fold it, or the mylar will develop permanent creases.

Used ProAiir Hybrid? Rub a thin layer of mild soap into the stencil first, then rinse with lukewarm water. This loosens the alcohol-based paint from the mylar.

For storage: hang the stencil from the tab hole, or keep it between two sheets of paper in a flat folder.

What can you use it for?

• Bodypaint: Topper 2 Princess as an accent or decoration in a full look
• Festivals and parties: Topper 2 Princess as a detail on cheek, shoulder or decolletage
• Theme parties: Topper 2 Princess for fantasy, glamour or fairytale looks
• Theatre and film: Topper 2 Princess for stage decorations or costume details
• Kids parties: Topper 2 Princess as quick cheerful makeup decoration

Contents

1 reusable ProAiir QuickEZ Topper 2 Princess stencil in flexible mylar (7 mil), approx. 11.4 x 14 cm, single design.

Other QuickEz stencils

If this princess and glamour theme fits your work, have a look at these stencils from the same range:

• ProAiir QuickEZ Beard and Mustache: a playful beard and moustache motif, great for fancy dress, theatre or kids' parties.
• ProAiir QuickEZ Crown Topper 1: a crown motif that pairs perfectly with the Topper 2 Princess for a complete royal look.
• ProAiir QuickEZ Eye Lashes: a lash detail for glamour and fantasy looks on the eyelid or cheek.

Browse the full ProAiir QuickEz range with more than 60 patterns and designs.

The product photo shows an example face- or body-paint effect with this stencil. The Mylar stencil itself is semi-translucent; the final colour depends on the makeup or airbrush paint you choose.