ProAiir QuickEZ Web Skin sjabloon

ProAiir QuickEZ Web Skin Stencil

The QuickEZ Web Skin stencil puts a realistic web pattern on face, neck or arm in one smooth move. Press it down, airbrush or sponge over it, lift it off and the effect is done. The quickest route to a horror look at any Halloween event or themed shoot.

The stencil works with an airbrush, a make-up sponge or a finger sponge. You pick whichever tool suits the job.

What is the QuickEZ Web Skin stencil?

A reusable make-up stencil made from flexible, semi-transparent 7 mil mylar (approximately 0.18 mm thick).

The designs shown in product photos are examples only. The colour that lands on the skin is entirely your choice of face paint or body paint.

Size: approx. 11.4 x 14 cm, one design per stencil. The tab has a hole so you can hang it on a keyring or stencil rack.

Why pick this stencil?

• Airbrush and hand application. The stencil works with ProAiir Hybrid, ProAiir Ink, Endura and also with a sponge and water-activated face paint. You choose the technique that fits the job.
• Fast results. Press, airbrush or sponge, lift, done. Perfect when you have a long queue of faces to get through at a Halloween event or horror show.
• Reusable. Mylar is tough and flexible. Clean it well, store it flat and it will last you many Halloweens.
• Follows the contour of the body. The thin, flexible mylar sits flush against cheeks, neck or upper arm without gaps.

How to use the stencil

1. Hold the stencil flat against the skin where you want the Web Skin pattern to appear.
2. Spray with the airbrush or dab with a damp make-up sponge.
3. Lift the stencil straight up. Do not slide it across the skin or the edges will smear.

Tip when using water-activated face paint: keep your sponge damp, not wet. Too much moisture and the paint seeps under the edges, leaving blurry lines.

Cleaning and storage

Rinse the stencil with lukewarm water and mild soap after use. Pat it gently dry and leave it to lie flat until completely dry. Do not roll or fold it, as the mylar will develop permanent creases.

Used ProAiir Hybrid? Rub a thin layer of mild soap into the stencil first, then rinse with lukewarm water. This loosens the alcohol-based paint from the mylar.

For storage: hang the stencil from the tab hole, or keep it between two sheets of paper in a flat folder.

What can you use it for?

• Halloween makeup: Web Skin on face, neck or arm for an atmospheric horror look.
• SFX and cosplay: Web Skin as a building block for zombie, vampire or grim-reaper characters.
• Bodypaint: Web Skin in a full body paint for Halloween parties or horror shows.
• Theatre and film: Web Skin for stage and camera work where speed matters.
• Festivals and photoshoots: Web Skin as a statement detail in a gothic or horror look.

Contents

1 reusable ProAiir QuickEZ Web Skin stencil in flexible mylar (7 mil), approx. 11.4 x 14 cm, single design.

Other QuickEz stencils

If this horror theme suits your work, take a look at these other stencils from the same range:

• ProAiir QuickEZ Blood Cells: blood cell pattern for realistic horror and SFX effects on skin or body.
• ProAiir QuickEZ Bloody Eyes: eye motif with blood-splash effect, striking as a detail on zombie or horror looks.
• ProAiir QuickEZ Centipedes: centipede pattern for a creepy crawling effect on arm, neck or chest.

Browse the full ProAiir QuickEZ range with over 60 patterns and designs.

The product photo shows an example face- or body-paint effect with this stencil. The Mylar stencil itself is semi-translucent; the final colour depends on the makeup or airbrush paint you choose.