ProAiir QuickEZ Skeleton Hand Large sjabloon

ProAiir QuickEZ Skeleton Hand Large Stencil

The ProAiir QuickEZ Skeleton Hand Large stencil puts a life-size skeleton hand on the skin in seconds. Press it down, airbrush or dab with a makeup sponge or finger sponge, lift the stencil off, done. The quickest route to a convincing skeleton look on the chest, shoulder or upper thigh.

What is the QuickEZ Skeleton Hand Large stencil?

A reusable makeup stencil made from flexible, semi-transparent mylar, 7 mil thick (approximately 0.18 mm).

The designs shown in the product photos are examples. The colour that lands on the skin is entirely your choice.

Size: approximately 17.8 x 22.9 cm, one design per stencil. The tab has a hole so you can hang the stencil on a keyring or stencil rack. This is the Large variant, suited to bigger hands and broader body areas like the chest, shoulder or upper thigh.

Why pick this stencil?

• Airbrush and hand application. Works with ProAiir Hybrid, ProAiir Ink, Endura and also with a sponge and water-activated face paint. You pick the technique that suits the job.
• Fast results. Press, airbrush or stamp, lift, done. Perfect when you're working through a long queue at a Halloween event or bodypaint show and still want a crisp skeleton motif every time.
• Reusable. Mylar is tough and flexible. Clean it properly, store it flat, and it will last through many Halloweens and shows.
• Follows the body's contours. The mylar is thin and pliable, so it sits flush on a rounded shoulder or curved chest without the edges lifting.

How to use the stencil

1. Hold the stencil flat against the skin where you want the skeleton hand.
2. Spray with the airbrush or dab with a damp makeup sponge.
3. Lift the stencil straight up. Do not slide it across the skin or the edges will smear.

Tip for water-activated paints: keep your sponge damp, not wet. Too much moisture and the paint bleeds under the edges, making your lines fuzzy.

Cleaning and storage

Rinse the stencil after use with lukewarm water and mild soap. Gently pat dry and lay it flat until completely dry. Do not roll or fold it, or the mylar will develop permanent creases.

Used ProAiir Hybrid? Rub a thin layer of mild soap into the stencil first, then rinse with lukewarm water. That breaks the alcohol-based paint free from the mylar.

For storage: hang the stencil from the tab hole, or keep it between two sheets of paper in a flat folder.

What can you use it for?

• Halloween makeup: skeleton hand on the chest, shoulder or upper arm for a life-size skeleton look
• SFX and zombie cosplay: rotting hand or grim-reaper element for horror photoshoots
• Day of the Dead: calavera total look with skeleton extensions across the body
• Theatre and film: zombie, grim reaper or skeleton character for stage or camera
• Bodypaint: skeleton total paint for festivals, shows or bodypaint competitions

Contents

1 reusable ProAiir QuickEZ Skeleton Hand Large stencil in flexible mylar (7 mil), approximately 17.8 x 22.9 cm, single design.

Other QuickEz stencils

Does the skeleton theme fit your work? These stencils from the same range are worth a look:

• ProAiir QuickEZ Skeleton Hand Normal: the same skeleton hand design in the smaller Normal size, ideal for narrower hands or children.
• ProAiir QuickEZ Spiderweb: classic cobweb motif for a Halloween look on the cheek or décolletage.
• ProAiir QuickEZ Crawling Spiders: crawling spiders as a repeating pattern, striking on the arm or neck.

Browse the full ProAiir QuickEZ range with over 60 patterns and designs.

The product photo shows an example face- or body-paint effect with this stencil. The Mylar stencil itself is semi-translucent; the final colour depends on the makeup or airbrush paint you choose.